Kindergartens & education
Courtyards, play and learning spaces, routes and daily maintenance. Review the equipment and information for each zone.
KRAIBURG RelastecManufacturer · Germany
EUROTEC / PLAY SPACE SOLUTIONS
Room to play.
Space to grow.
EUROTEC brings surfacing, play elements and finishing details into one coordinated space. Select EUROFLEX products around the users, equipment data and substrate — from kindergarten courtyards to parks and hospitality.
Bring the space together.The surface, the play elements and the edges — considered as one.
The activity above
Who uses the space, which play equipment is installed and which zones need separate consideration.
The layers below
The substrate, drainage and tested system alongside the product and finish.
The details around
Edges, transitions, levels and accessibility requirements within the same design.
01 / PEOPLE & PLACE
Different spaces.
The right starting questions.
Start with the people and the purpose of the space. Collect the information needed to review the product family and configuration.
Parks & public spaces
Bring surfacing, play elements and borders together with substrate design, drainage and circulation routes.
Hotels & hospitality
Design the play area as part of the wider experience, considering its location, neighbouring uses and installation constraints.
02 / THE EUROFLEX RANGE
Three product worlds.
A considered selection.
37 families from the EUROFLEX range, with documents beside each family. Mark options for review and collect the site information for a planning discussion with EUROTEC.
A product family, colour or thickness is not an approval of suitability for equipment. Impact surfacing, play elements and borders are reviewed for their purpose and the documents of the exact configuration.
No families match this search. Try a different term or filter.
Slabs & surfacing systems
Impact Protection Slab
Recycled-rubber slabs for playground surfacing, with connector-pin installation and configuration-specific impact protection.
Family specifications & documents
Installation instructions · PDF ↗Installation instructions · Softsystem · PDF ↗Product family on the manufacturer website ↗
The EPDM specification is not the specification for the regular recycled-rubber slab. Documents for the requested configuration are reviewed with the team.
Slabs & surfacing systems
Impact Protection Slab EPDM
Recycled-rubber base slabs with a coloured EPDM surface for playground and recreation areas.
- Unit dimensions
- 500 × 500 mm
- Slab thicknesses
- 30 / 40 / 50 / 55 / 70 / 80 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Installation instructions · Softsystem · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: March 2026
The 90 mm Softsystem build-up comprises a 70 mm slab and a 20 mm underlayer, as listed in the family document.
Slabs & surfacing systems
Impact Protection Slab EPDM Multicolor
EPDM-surfaced impact-protection slabs with a blend of two or three EPDM colours.
- Unit dimensions
- 500 × 500 mm
- Slab thicknesses
- 30 / 40 / 50 / 55 / 70 / 80 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Installation instructions · Softsystem · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: March 2026
Slabs & surfacing systems
Impact Protection Slab EPDM Mulch
Impact-protection slabs with a textured EPDM mulch surface for outdoor play and recreation areas.
- Unit dimensions
- 500 × 500 mm
- Slab thicknesses
- 30 / 40 / 50 / 55 / 70 / 80 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Installation instructions · Softsystem · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: January 2019
Slabs & surfacing systems
Soft Touch
A recycled-rubber slab base with a soft polyamide-flocked fabric surface; fall-height performance depends on the complete listed configuration.
- Unit dimensions
- 500 × 500 mm
- Slab thicknesses
- 30 / 40 / 50 / 55 / 70 / 80 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Installation instructions · Softsystem · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: October 2025
Softsystem configurations include a 20 mm base frame and are reviewed as separate build-ups according to the document.
Slabs & surfacing systems
Soft Grip
Rubber-base slabs with a textured fabric/PVC-granulate surface for walkways, sloping surfaces and barrier-free access areas.
- Unit dimensions
- 1000 × 1000 × 30 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: November 2025
Slabs & surfacing systems
Letter & Number Slab
Letter and number motifs integrated into slabs for learning and hopping games in school and childcare play areas.
- Unit dimensions
- 500 × 500 mm
- Slab thicknesses
- 30 / 40 / 50 / 55 / 60 / 70 / 80 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Installation instructions · Softsystem · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: March 2021
Slabs & surfacing systems
Design Slab
Motif slabs for combining creative surface designs with school and childcare play areas.
- Unit dimensions
- 500 × 500 mm
- Slab thicknesses
- 30 / 40 / 50 / 55 / 60 / 70 / 80 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Installation instructions · Softsystem · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: March 2021
Slabs & surfacing systems
Visual System
Individually printed vinyl design flooring over an elastic slab system, with each build-up selected for the intended indoor application.
- Slab layer
- 30–80 mm
- Surface layer
- 2.9 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: February 2024
Data applies to defined build-ups. A 20 mm Softsystem underlayer is included only in the listed configurations.
Slabs & surfacing systems
Visual System comfort
Individually printed design flooring over a thin sound-reduction layer for spaces without a prescribed fall-protection requirement.
- Underlayer
- 4 mm
- Surface layer
- 2.9 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: February 2024
The comfort data sheet does not contain a fall-height table. Do not infer its suitability as equipment impact protection surfacing.
Slabs & surfacing systems
Outdoor Games
Modular floor sets for chess, draughts, Ludo and Nine Men's Morris, with playing figures and optional perimeter profiles.
Family specifications & documents
Slabs & surfacing systems
Aqua slab
EPDM-surfaced slabs developed for water and spray parks, with product-specific wet barefoot-slip and water-exposure test data.
- Unit dimensions
- 500 × 500 × 30 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: March 2026
Refer to the dedicated Aqua data; data for other EPDM slabs is not Aqua test data.
Slabs & surfacing systems
Sports pavement slab
Dense rubber sports slabs for outdoor ball-play surfaces, with product-specific ball rebound and critical fall-height data.
- Unit dimensions
- 500 × 500 × 30 / 40 mm; 1000 × 500 × 40 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: March 2026
Slabs & surfacing systems
Paving block tile
Rubber paving-pattern tiles supplied with connector pins for paths, walkways and recreation surfaces.
- Unit dimensions
- 500 × 500 × 40 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: March 2026
Slabs & surfacing systems
Elastic pavement blocks
Interlocking rubber paving blocks, with full, half and starter units for paths and recreational surfaces.
- Full unit
- 200 × 165 × 43 mm
- Half unit
- 100 × 165 × 43 mm
- Starter unit
- 200 × 140 × 43 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: May 2026
Slabs & surfacing systems
Protect
Large rubber slabs intended for concentrated wear areas beneath slides and swings.
- Unit dimensions
- 1000 × 1000 × 40 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: October 2021
Slabs & surfacing systems
Multiground
Perforated rubber matting for stabilising natural surfaces and slopes; tested fall-height values depend on the ground beneath it.
- Unit dimensions
- 110 × 175 cm
- Slab thicknesses
- 24 mm
Family specifications & documents
Data sheet · PDF ↗Installation instructions · PDF ↗Product family on the manufacturer website ↗
Dimensions are from the linked family document; they are not a fall-height selection rule. Edition: June 2026
The ground beneath the mat is part of the test and suitability conditions.
Play & design elements
Balls and half balls
Rubber balls and half balls for seating, play routes and spatial definition; anchoring depends on the model and application.
Play & design elements
Diamond
Full and half dodecahedral rubber elements for seating, balance routes and spatial boundaries.
Family specifications & documents
Play & design elements
Cube
Rubber cubes for seating islands, play-space boundaries and sandbox arrangements.
Family specifications & documents
Play & design elements
S- & C-Blocks
Curved S- and C-shaped rubber blocks for seating, balance routes and flexible spatial layouts.
Family specifications & documents
Play & design elements
Animals
Elephant, rhino, dromedary and pony forms for play areas and small seating islands.
Family specifications & documents
Play & design elements
Stepper
Rubber stepping elements for arranging activity and balance routes.
Family specifications & documents
Play & design elements
Mushrooms
Mushroom-shaped rubber elements in different heights for play routes and seating arrangements.
Family specifications & documents
Play & design elements
Trees
Rubber tree forms with different crown sizes and trunk heights for themed play landscapes.
Family specifications & documents
Play & design elements
Rocks
Rubber rock forms for combining with tree elements or using as standalone play-landscape components.
Family specifications & documents
Play & design elements
Turtle
Turtle-shaped rubber play and seating element with a coloured EPDM surface.
Family specifications & documents
Play & design elements
Caterpillar head
A caterpillar-head design element for combining with half balls to create a themed sitting or play route.
Family specifications & documents
Borders & transitions
Modular sandbox edging
Reinforced modular rubber elements for forming flexible sandbox perimeters.
Family specifications & documents
Borders & transitions
Edge and corner profiles
Sloped edge and corner profiles for finishing transitions at slab-surfacing boundaries.
Family specifications & documents
Borders & transitions
Lawn edging
Rubber edging for separating surfacing and lawn areas, including variants with an EPDM finish.
Family specifications & documents
Borders & transitions
Rubber palisades
Rubber palisades for landscape boundaries and changes of level.
Family specifications & documents
Borders & transitions
Step blocks
Rubber step blocks for landscaped circulation routes and changes of level.
Family specifications & documents
Borders & transitions
Edge protector
Rubber covers for exposed concrete, wood and metal edges, stairs and similar built elements.
Family specifications & documents
Borders & transitions
Protective edging
Flexible rubber edging for active areas and trampoline-frame or spring boundaries, with model-specific connector details.
Family specifications & documents
Borders & transitions
Perimeter panels
Rubber panels for covering perimeter surfaces around play and recreation areas.
Family specifications & documents
Borders & transitions
Edge protection profile
Rubber corner profiles for covering exposed built edges in play, school and childcare environments.
Family specifications & documents
03 / THE COMPLETE SYSTEM
Start with the information.
Review the whole system.
Equipment free fall height and a surface test result are different pieces of information. Obtain the equipment data from its documentation or designer, and review the flooring system together with its substrate and installation details.
- 01Equipment & zone information
Collect the reported free fall height and its source, areas, dimensions and separate information for each zone. - 02Product family & configuration
Check the model document, material, thickness and complete system. Do not transfer a test result between different families. - 03Substrate & interfaces
Coordinate drainage, flatness, slopes, joints, edge details and transition levels. - 04Installation & maintenance
Coordinate installation, checks and maintenance in accordance with system documents and project requirements.
04 / COLOUR, FINISH & PLAY
Material, colour and play.
One language for the space.
Explore finishes, combine elements and confirm colours against a physical sample. Images and design tools do not replace the product and system specification.
EPDM colours on the manufacturer website ↗PLAYGROUND CONFIGURATOR
See the elements together.
The manufacturer’s tool illustrates play areas and combinations of surfaces and elements. It is not an approved safety design.
Open the manufacturer configurator ↗COLOUR & MATERIAL
Choose colour through material.
Explore EPDM colours and mixing options. Family compatibility, finish and order quantities are checked before supply.
Manufacturer colours & colour tools ↗
05 / TECHNICAL LIBRARY
The right document.
For the right family.
Data sheets, installation and care documents in their original languages. Environmental and quality documents must be checked against their listed products and scope.
Open the EUROFLEX English catalogue · PDF ↗
DOWNLOADS
EUROFLEX document library
Manufacturer information organised by product and document type.
Open manufacturer source ↗TESTINGImpact protection & testing
Testing and system information with distinctions between product families and configurations.
Open manufacturer source ↗COLOURSEPDM colours
Explore colours and mixes. Final confirmation is based on a sample and specification.
Open manufacturer source ↗COMMON QUESTIONS
Questions that move
the project forward.
Is slab thickness enough to make a selection?
No. Review the family, material, finish and tested system together with the equipment information and substrate. The same thickness in different families can be associated with different test results.
Is every rubber element impact protection surfacing?
Play, design and border elements have their own purposes and documents. Do not assume they replace a surfacing system tested for the required configuration.
What if the free fall height is not yet known?
Mark it as unknown in the brief. Complete the value and its source using the equipment documents or designer. The tool does not calculate it from the overall height of the equipment.
How do Visual System and Visual System comfort differ?
They are separate families with different constructions and scopes. Review the applicable family document and do not transfer impact protection or installation results between them.
What should be considered about sunlight and shade?
Elastomeric surfaces can become hot in direct sunlight. The impact protection slab installation guide recommends shading wherever possible. Review shade, drainage and the substrate together with the intended use. Manufacturer installation guide · PDF ↗
Is the entire range available to order in Israel?
This page presents manufacturer product families. Supply options, quantities, dimensions and colours are checked with EUROTEC for the requested model and configuration.
Are these photographs of EUROTEC installations?
The photographs and illustrations are supplied by KRAIBURG Relastec to show products and applications. They are not presented as projects installed by EUROTEC.
YOUR SPACE / YOUR PROJECT
Every zone.
One clear picture.
Mark families for review, add project zones and collect the information available. Copy or download the brief and attach it to your enquiry to the team.
The draft stays in this browser tab. The tool does not send an enquiry. All information is available without completing the fields.
Project information
Project zones
Keep information separate for each zone. You can record what is not yet known; the tool does not automatically choose a product from these values.
Families marked for project review
Mark product families in the catalogue, or start with the site information.
A brief for coordination and suitability review with EUROTEC. It is not a safety approval or an installation specification. The system configuration, suitability for the equipment and supply options require professional confirmation.
EUROTEC / SOLUTIONS FOR YOUR PROJECT
Specialist solutions.
One EUROTEC team.
EUROTEC coordinates product selection, specifications and supply for the project requirements. The range includes SPORTEC for sport and fitness, EUROFLEX for play and SHIELDTAC for shooting facilities, manufactured by KRAIBURG Relastec.
EUROFLEX
Play spaces, childcare & borders
The range presented on this page, covering surfacing, play elements and finishing details.
Product families ↑SPORTEC
Sport, fitness & acoustics
Flooring for training spaces, elastic layers and Gymcoustic systems.
Explore SPORTEC →SHIELDTAC
Shooting ranges & training centres
Dedicated rubber systems for the floor and envelope of shooting facilities.
Explore SHIELDTAC →Product images, application photographs and illustrations: KRAIBURG Relastec. Screen colours are illustrative. Product selection, configuration and supply options are reviewed with the team for the project requirements.